How to Clean Gaming Keyboard
Dust and filth will clog a keyboard’s switches and circuitry long before they break. The most vital keyboard maintenance duty is to keep it clean with the contaminants. Though spills are a different story, thus they’ll have their area.
There are a few cleaning suggestions that help you in how you can clean your Quiet Gaming Keyboards without damaging them.
Regularly, you should lightly wipe your keyboard. It’s crucial to keep grime collection away and become extremely challenging if you eat near to your keyboard. The painted metal plate that supports each key switch will partially fuse with dust and food over time. Hence, to avoid such particles must be brushed away once attached, which is both unpleasant and inconvenient.
Use the following procedure to perform preventive cleaning:
- Remove your keyboard from the outlet.
- To clean the dust from the plate, use a vacuum. The Best Logitech Gaming Keyboards can be obtained by softly pressing the vacuum’s attachment tube on the keycaps. It is suggested to use small handheld vacuum cleaners with no moving brushes for more effective results.
- After vacuum use a damp microfiber cloth and clean the entire keyboard.
- Lastly, dry the keyboard by using another cloth.
Some dirt is persistent, so instead of vacuuming and wiping it down regularly. You need to put in the extra effort. Additionally, a layer of finger oils will accumulate on your keyboard’s keycaps over time. Fortunately, there are tried-and-true solutions for resolving those problems.
Use the following procedure to perform deferred cleaning:
- Turn off your computer and unplug your keyboard.
- Remove the keycaps from your keyboard with a keycap puller. The majority of large keys (space, enter, shift, etc.) are wire-stabilized, making them more difficult to remove. It’s advisable to wipe them clean with a slightly moist microfiber towel if you don’t feel comfortable removing and reseating them.
- Denture pills or dish soap can be used to clean the keycaps.
- In the meantime when keycaps soak, use a small stiff brush or a q-tip to loosen those particulates that are clung to the plate. Make sure the brush bristles should not be near switch stems. Dust could be pushed deep into a switch by the bristles, also avoiding vacuum removal.
- Thoroughly vacuum the plate with a handheld roller-less type or the attachment tube of a full-size machine. Turn the keyboard upside down and allow any loose particles to fall off if the vacuum won’t pick it up.
- If there is a goo-covered place on the plate, wipe it up with a little wet towel or a Q-tip.
- Other little cleaning equipment can also be used. If at all possible, avoid moistening the keyboard switches.
- To avoid dust collection, place the keyboard face down while the keycaps dry.
- All keycaps should be replaced.
- Using a somewhat damp microfiber cloth, wipe clean the case. Instead of using paper towels, dry them with another cloth. Particles and scrapes are left behind by using paper towels.
Perhaps you decided to buy a secondhand keyboard. Let’s pretend the previous owner kept it in a dingy basement and liberally sprinkle the chunks of Cheetos amongst the keys. Or perhaps you were the prior owner. We’re not here to pass judgment, especially if you’re trying to clean up your act. This tutorial is for keyboards that are filthy on both the inside and outside. If you follow it, your warranty will be voided, if it is still active.
Continue with the following steps after completing stages 1 and 2 in the Deferred Cleaning guide:
- To clean the grime from the keycaps, consider using an ultrasonic cleaner. They’re also fantastic for cleaning jewelry and toys around the house. If you don’t want to use then just use the keycap soaking method prescribed in the Deferred cleaning guide.
- Lay the keycaps out to dry with the plus-shaped stem facing up once they’re finished. The leftover water may take some time to evaporate completely.
- Carefully remove the keyboard case from the keyboard. Make sure the screws are stored in a container. If they’re different sizes, grouping them will make reassembly easier. If any cords need to be disconnected, do so with caution. If you’re having difficulties remembering what belongs where take pictures using your phone.
- Remove the PCB and plate from the keyboard after it has been disassembled. If the dirt and grime aren’t too bad, you can vacuum the inside of the case halves with a brushed attachment. After that, wipe down the area with a moist cloth.
- If the mess is serious (and there are no electronics attached to the case), clean the case halves in a dish soap solution with a medium-strength bristle brush. Allow water to evaporate from regions that cannot be accessed after carefully rinsing and drying both sides with a cloth (like screw holes).
- Scrub the plate with a small stiff-bristle brush to dislodge any particle debris that has stuck to it. Brush bristles should not be near switch stems. Dust could be pushed deep into a switch by the bristles, impeding vacuum removal.
- Wipe a goo-covered place on the plate with a slightly damp towel or a Q-tip. Other small-sized cleaning equipment can also be used.
- If at all possible, avoid moistening the keyboard switches.
- While the other components dry, place the clean plate and PCB face down to minimize dust collection.
- After everything has dried, reinstall all stabilized keys that are close to the case’s edge. Examples include the space bar, keypad plus, and keypad enter. If the stabilizers are rattling, you can oil them.
- Put the keyboard together.
- Replace the keycaps on the keyboard.
How To Deal With Spills:
Typically the worst enemy of any mechanical keyboard is spilled.
Though, water isn’t that extremely dangerous if you promptly unplug your keyboard if an accident happens. And wait to let it dry for a long time. However what happens when flavored drinks (especially sweet ones) spill? It might cause major problems.
Firstly, when a spill happened, make sure don’t flip the keyboard or tilt it.
Furthermore, even after the spill has fully dried, do not test the keyboard on your computer.
As it could harm the USB port or may cause the machine to freeze up by spamming key presses. After using any cleaning method a Deferred Cleaning or Advanced Cleaning, if the liquid did not get into the switches or fry anything critical, you can continue to use the keyboard. Else buy a new keyboard or you can do soldering where you can take off all of the switches on a keyboard then dismantle and clean each switch and keyboard component.
You could also repair any switches that have been damaged by the spill.
But this is not a suggested practice because the method is time-consuming and labor expenses.